Veteran Garage Door Repair | Keller TX | 817-769-8488

0
58
Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You may find that your garage door opener has been giving you troubles, so you require to repair it. You can fix it by changing a circuit card, a photo-eye sensor, the primary drive gear, or the set-limit buttons. You can likewise check if the safety sensors are working effectively.

Changing a motherboard

Replacing a circuit board for your garage door opener needs a couple of steps as well as tools. Initially, you require to shut off the circuit breaker as well as disconnect any kind of cables. Next off, open the motherboard cover. This will certainly help you to diagnose the trouble as well as establish if you need a brand-new board. Next, remove the old board and also its cable ports.

You can then continue to change the circuit board. The replacement procedure is very easy as well as takes around 10 mins. A new circuit board will cost regarding $80. To protect your brand-new circuit card from power surges, you can buy a surge protector.

Replacing a photo-eye sensor

Replacing a photo-eye sensor can be a fairly simple job. Initially, eliminate the sensing unit from the door as well as ensure it is located correctly. If the sensing unit is angled at all, it may not be getting the appropriate signal, which might be creating the blinking lights. If you discover that the photo-eyes are out of placement, you may require to have actually a specialist come and fix the issue.

The photo-eye sensing unit includes two items that place outside of the door tracks and toward the flooring. The photo eyes will have a tiny LED light as well as need to be solid in shade. If the light is blinking, its likely the photo-eye is defective as well as will certainly need to be changed.

Replacing a primary drive equipment

To replace a garage door opener primary drive gear, beginning by removing the cap from the chain wheel. Next, remove the two screws holding the drive equipment to the gear assembly. Now, you can loosen the three tension pins. Press them from both sides and afterwards remove them. After that, detach the three cables from the garage door opener motor. These cords need to be white, red, as well as blue.

When you have actually eliminated the old equipment, mount a new one. Make certain to oil it well. Put the brand-new equipment into the shaft, seeing to it to line up the placing holes. See to it the equipment and also sprocket assembly are positioned properly to ensure smooth procedure. Next off, utilize a hammer and a nail to drive a pin right into the brand-new equipment.

Changing the set-limit buttons

The first point you should do if your garage door is not working appropriately is to inspect the set-limit buttons. You might require to change them to make sure that the door closes earlier or stops prior to it gets to the flooring. You can check this by checking out your garage doors handbook or online.

To change the set-limit switches, youll require a screwdriver or outlet. Change the handle clockwise or counterclockwise until the door goes up and also quits, or lowers its range. To check for proper travel distance, gauge the void from all-time low of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Main St Ste 105, Keller, TX 76248, United States

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488